|
|
Post by Rhubarb on Dec 7, 2015 19:39:12 GMT 1
Hi all, spent most of the day experimenting today. I could do with some help.. If I weld the internal angles I can't grind away without rubbing away at the angle of the box section. The one on the left I haven't welded(the internal)so I've put a touch of seam sealer in the gap.. So do I carry on like that, or invest £50 in a powerfile? Will a powerfile do the job?  Attachment DeletedAttachment DeletedAttachment Deleted |
|
|
|
Post by Noberator on Dec 8, 2015 11:01:05 GMT 1
Hi all, spent most of the day experimenting today. I could do with some help.. If I weld the internal angles I can't grind away without rubbing away at the angle of the box section. The one on the left I haven't welded(the internal)so I've put a touch of seam sealer in the gap.. So do I carry on like that, or invest £50 in a powerfile? Will a powerfile do the job? View AttachmentView AttachmentView Attachment Never been shown or tried.  |
|
|
|
Post by chippie on Dec 8, 2015 13:59:08 GMT 1
I dont understand why you cant dress the welds?
Care to explain?
|
|
|
|
Post by Rhubarb on Dec 8, 2015 14:49:22 GMT 1
Chippie: I make a frame from the box section, and the inside corners if you looking at it side on are the awkward ones. Because the access is bad and the flapwheel is thick its impossible to achieve anywhere near a perfect finish. Bearing in mind the edges of the box section are rounded. I'll upload a clearer photo later  |
|
|
|
Post by chippie on Dec 8, 2015 16:01:28 GMT 1
Ah...you didnt say what you was using for weld cleanup....
How about a die grinder?
|
|
|
|
Post by Joepublic on Dec 8, 2015 17:38:31 GMT 1
Try a grinding disc rather than a flap wheel? Maybe dress the disc to a 45 degree bevel at the end to get into the corner?
|
|
|
|
Post by Rhubarb on Dec 8, 2015 18:15:11 GMT 1
Ah...you didnt say what you was using for weld cleanup.... How about a die grinder? Good idea, but I haven't got a big enough compressor to run one |
|
|
|
Post by Rhubarb on Dec 8, 2015 18:16:02 GMT 1
Try a grinding disc rather than a flap wheel? Maybe dress the disc to a 45 degree bevel at the end to get into the corner? That's a great idea |
|
|
|
Post by Rhubarb on Dec 8, 2015 18:26:53 GMT 1
So this is where I'm up to  So this is the problem area  Getting there  |
|
|
|
Post by chippie on Dec 8, 2015 18:34:40 GMT 1
Worrizit mista?
I know, I know......its a stand for a big fish tank.......
|
|
|
|
Post by Rhubarb on Dec 8, 2015 18:40:51 GMT 1
Worrizit mista? I know, I know......its a stand for a big fish tank....... It's going to be a coffee table |
|
|
|
Post by Joepublic on Dec 8, 2015 19:09:29 GMT 1
Worrizit mista? I know, I know......its a stand for a big fish tank....... It's going to be a coffee table With a V8 in the centre? |
|
|
|
Post by Noberator on Dec 8, 2015 19:41:49 GMT 1
Worrizit mista? I know, I know......its a stand for a big fish tank....... It's going to be a coffee table Thank goodness for that.  I thought you was making coffins to order .  |
|
|
|
Post by Rhubarb on Dec 8, 2015 19:44:11 GMT 1
It's going to be a coffee table With a V8 in the centre? Unfortunately not, I sold it |
|
|
|
Post by Joepublic on Dec 8, 2015 20:04:34 GMT 1
Unfortunately not, I sold it Is this a business venture? |
|
I thought you was making coffins to order . 